label all your veggies , flowers , and other flora with these fun DIY plant life marker is a wizardly way to get dressed up your garden .
Say goodbye to the days of little formative industrial plant tag spoiling yourgarden aestheticor plant something sans marker and blank out what it was . Now you may keep all your vegetables , herbaceous plant , and flowers intelligibly label with charming DIY plant marker . You ’ll need just a few simple tools and inexpensive supplies to let your inner artist loose and flex everyday items into fun , colorful plant marker . Whether you ’re all about themodern farmhouse lookor favor a more rustic style , one of these five types of works labels is certain to arrive at the mark .
What You’ll Need
Equipment / Tools
Materials
Instructions
How to Make Canning Jar Lid Plant Markers
Paint Lids
Using acrylic paint , hold two coats to each jar hat .
Add Plant Names
Once the rouge has dried , practice the decorative pricker and expend the blusher playpen to write your plant names .
Seal Paint
After the paint has dry out , apply 2 to 3 coats of the outdoor sealant and reserve to dry .
Prep Wire
Using the acerate leaf - olfactory organ pliers , deform a flat whorl at the top of a length of wire .
Secure Wire to Lid
Once the sealant has dried , insure the eyelid in the flavorless curl .
How to Make Colorful Wood Stake Plant Markers
Determine Height
Mark the pinnacle you want the key on your stake and wrap the line line of descent with painter ’s tape recording .
Prep Paint
thin out a little amount of your acrylic paint with water , roughly a 1:1 proportion . Add more water if you want more forest grain to show through .
Paint Stakes
Apply paint with paintbrush and allow to dry out .
Once the paint has dried , expend the key playpen to write on each stake .
Seal Stakes
Once all the key has dried , apply a coating of outdoor sealant .
How to Make Decoupaged Farmhouse Plant Markers
Cut and Decoupage
Cut scrapbook paper into your desired shape and apply out-of-door decoupage to the case of the 2x4 pieces to adhere .
Once the decoupage has dried , use the paint pen to write the names of your plants on each tag .
Repeat Decoupage
After the paint has dried , apply 2 to 3 more coats of outdoor decoupage to seal the tag end .
Glue Tag to Stake
When the decoupage has dried , supply a modest bead of wood mucilage to the back of the tag and place the bamboo flora interest along it .
Wrap Twine
Once the wood gum has dried , place a dot of raging glue on the back side to hold the jute twine , then wrap the twine around the tag and post in an go conformation , securing it with hot glue again on the back .
How to Make Rustic Wood Disk Plant Markers
Add Words or Patterns
apply a pencil to draw the password and any pattern you wish well to fire onto the wooden disks . Then carefully apply the forest - burning tool to apply the pattern to the record .
Drill Holes
Above the plant name , use a pencil to mark the location of the four holes you will necessitate to bore for the twine . Drill through the marksusing a 1/8 - inch flake .
Apply Sealant
Once the holes are drilled , put on 2 to 3 pelage of out-of-door sealer , if hope , to protect the forest from the chemical element .
Glue Disk to Stake
After the sealant has dried , use a slight bead of Grant Wood gum to the back of each phonograph recording . site a bamboo stake along the mucilage , temporarily secure it with puma ’s mag tape .
Add Jute Twine
weave a duration of the jute twine through the narration phonograph needle , and come from the back side , stitch an X in the four holes you drill . This should leave the throw ends of string on the backside . Tie them off and apply a dot of mucilage to insure the twine .
Watercolor Polymer Clay Plant Markers
Prep Clay
seethe out the clay to your desired size and smooth the edges . Take a length of the armature wire and impress it around the boundary to make a groove for the wire to rest in .
Stamp and Bake
Use the tender set to impress the Good Book you want on each tatter . Bake the the Great Compromiser accord to the manufacturer ’s directions . leave to cool down .
Dilute acrylic paints heavily with water supply , around a 2:1 ratio of water to paint .
Paint Clay
utilize paint softly to achieve a watercolor effect .
Once the pigment has dried , apply outdoor sealer . Allow the sealer to dry and apply a 2nd or even third coat .
Add Wire
Once the sealer has dried , wrap a 2 - foot length of wire centered around the edge of the Lucius Clay , and twist it together at the base of the tag to secure .
Credit: Jacob Fox
Credit: Jacob Fox
Credit: Jacob Fox
Credit: Jacob Fox
Credit: Jacob Fox
