How To Remove An Echo Edger Blade [Step By Step Guide]

An Echo edger is an good pecker for divide grass from walkways providing premises with a neat , well - kept visual aspect .

However , the requisite to exchange the blade will come up at some point , and you will need to have sex how to do so . require to know how to remove it ? Well , we did some research , and here ’s what we get hold .

Here are the steps for removing the Echo edger blade :

In this clause , we will detail each of the steps above . We ’ll also go over how to put in a unexampled blade , which blades work with an Echo edger and other things . So keep on reading !

How Do You Remove An Echo Edger Blade?

Damaged , bent on , and dull are the frequent reasons for supercede the Echo edger blade . And so , learning how to remove the steel is necessary before you install a new replacement .

you could remove it chop-chop with just a few coarse peter and steps detail below .

1. Shut The Engine Off

cut off the edger ’s office will assure everyone ’s prophylactic throughout the facility . To do this , allow the engine to return to idle by relinquish the throttle gun trigger .

Then , slide the electrical switch button backwards to the STOP status .

2. Apply Lubrication

It make a barrier between the nut and the washer , make up removing it round-eyed . You may use a WD-40 to loose the rusted blade fasteners .

Click here to see this WD-40 on Amazon .

3. Remove The Pin

There is a split up pin in the hole in the front . It is a metal pin that secure the meeting place . To remove it , expend prospicient nose pliers or any tool to strengthen as needed and overstretch it out of the hole .

See this pair of recollective - nose plyers on Amazon .

This stick parry you from getting through the inner blade adapter . Also , this is the most ambitious part because you need to wield effort to absent it . It is not an easy - peasy move out procedure .

4. Insert A Locking Tool

This will help hold back the power take - off ( PTO ) shaft from turn because the leaf blade can freely splay , take a shit it hard to move out the blade .

To do this , move around the edger on its side , then trace up the maw in the interior sword adapter with the mountain pass in the gear housing and introduce the lock tool .

The locking tool was already included in the software when you bought the Echo edger , but if you lost it , you might apply an Allen wrench as an choice .

See this Allen wrench set on Amazon .

5. Loosen The Blade Nut

habituate a ratchet with a ½ " or ¾ " socket to relax the vane freak , specifically the left - handed ( LH ) screw thread . But it ’s better to buy a socket coiffe so you’re able to adjust and see what it fits .

Then , insert it into the spindle nut .

Click here to see this socket set on Amazon .

The brand washing machine underneath the nut indicates the constrain counselling , which will serve you determine which way to relax the blade nut .

Because the way of life to stiffen is counterclockwise , the loosen direction is clockwise . If necessary , invert the rachet ’s counseling using its mastery lever .

6. Remove The Blade

Once it is loosened , remove the fruitcake , automatic washer , and blade . Although the sword is typically deadening , still proceed with care .

It is possible to recycle or throw away the sword . You will utilize the spindle nut and washer with the replacement blade , so carry through these and salt away them safely .

Below is a YouTube video that will help you realise how this occur :

How To Install New Echo Edger Blade

It will be simple to instal the newfangled blade for your Echo edger once you acknowledge how to move out the onetime one . Reverse the procedure , and you ’re done . Details are providedbelow .

1. Prepare The New Blade

Usually , there are two blades in a pack . slice up the promotional material material with the box cutter . you could keep the label of the blade so you could apply this to take the correct brand the next time .

Click here to see this boxwood cutter on Amazon .

2. Examine The Spindle’s Surface

verify there is n’t any debris or dirt in the way of the young steel sit correctly over the hub . Brush out if you regain some , and you may also apply it with lubricator for rust shelter .

Click here to see this brush on Amazon .

See this rust bar and lube on Amazon .

3. Insert The New Blade Over The Spindle Hub

Ensure that the entire steel fits snugly on the mandril . The blade is positioned right as long as it is over the hub and gist .

4. Put Back The Fasteners

Put the automatic washer first over the new blade , then the nut . Hand - tighten the nut counterclockwise until it is befittingly set and fasten . Use a ratchet to tighten the nut completely .

However , the washing machine shows you how to tighten the testis if you use a Modern set of holdfast .

5. Install New Pin

Put the replacement rent pin in place , constrain the nut , and bend the pin ’s two legs counterclockwise around the PTO shaft . Never use an sometime split pin again .

6. Test Your Edger Blade

avow that the edger blade is hard attached to the spindle . Test your edger in a impregnable place .

Check the blade of your edger after each use to secure the spindle nut is impregnable and that the sword has not suffered any significant damage .

What Blade Does An Echo Edger Take?

It is essential that the type of blade and the size of the stuff being cut equal . Serious personal wound might result from a dull or improperly sharpened vane .

Blade sharpness is a must . injury to you and bystanders are more likely when using muted leaf blade .

The most compatible leaf blade for the Echo edger has a received thickness of 0.09 ” or a exchange premium one of 0.18 ” thick . Moreover , give birth a duration of7.75”but 8 ” is also satisfactory , and the most uncommitted replacement and arbor sizes are about 0.98 ” .

See this Echo edger steel on Amazon .

These size make it simple to butt around driveway , path , and walkway . These tough brand are made of corroding - resistant , high - persuasiveness brand .

to boot , it delivers special operation , lastingness , and cut off timbre while extending the equipment ’s lifespan by regularly swap out worn - out and muted blade .

How Do You Sharpen Edger Blades?

Edger blades that are too dull start to tear and rend at the grass instead of cutting it flawlessly . Luckily , there are dewy-eyed solution to the plaguey issue of a thudding edger vane .

There are a variety of ways to sharpen this pecker which will be discussed below :

Consult The Edger’s Manual

Always read first the owner ’s instructions for the lawn edger you have .

If you own an electric or gas lawn edger , the owner’smanualcan warn you not to endeavor to sharpen the blade .

Bevel The Blade’s Leading Edge

To ensure that soil is forced onto the blade , bevelthe front edge with rhombus dia - acuate stone . A minute cut boundary on a tart tool increases the pressure for each square in of soil .

See this baseball field dia - sharp Harlan F. Stone on Amazon .

In universal , it is advised to reach for a 20 - stage angle at the bevel for light - duty shaft and a higher angle for profound - obligation tools but for Echo ; it ’s a 30 - degree angle .

Please be cognizant that sharper is not needs better when it comes to edger or other horticulture putz . examine to keep the blade ’s bevel slant the same .

Making the angle too sharp can weaken the blade ’s border and get it to wear out after only a few uses .

Using An Angle Grinder To Sharpen

Hold the slant grinder where the disc is vertical to the blade ’s thin border to focalize the vane . To pull down out any notch , move the slant grinder back and onward along the blade ’s edge .

Click here to see this angle grinder on Amazon .

Keep the grinder invariably moving and only transfer a piffling amount of metal at a time because the grinder swiftly eliminates alloy . Observe the heighten slant apply in the manufacture .

To give an musical theme of how it is done , a video on YouTube is shown below :

Sharpening File

you could also polish the brand with a sharpening file . The proficiency for using it are usually write in the manual of arms . Just procure the edger blade in a vice .

Then expend the data file by move it onward evenly , do not move it toward you .

Click here to see this bench vise on Amazon .

snap here to see this file mark on Amazon .

Sharpen the blade until you find a burr execute the full distance of the press cutting boundary . Making soft stroke around the backside can help you extinguish the burr . finish up by apply a few light strokes to the bevel side .

Clean The Blade

Remove any corrosion , grime , and debris from the leaf blade before you sharpen it . This is a smart sustainment plan of attack , even if you do n’t intend to sharpen the sword . apply a scour pad or a stiff brush to strip the blade .

See this purge stamp pad on Amazon .

To Finish

The operation of the Echo Edger depends on decent maintaining its components . withdraw and replacing the old , deadening , or damaged blade will make a more effective and efficient grass - turn off job for you . We sincerely hope this entropy was helpful to you .

Made it to the end ? Check out these helpful related posts :

My Echo Edger Wo n’t Start – Why ? What To Do ?

Can I Use An Edger To poke A Trench ?