Home»Garden»Irrigation

Last Updated on August 9 , 2023

Do n’t spend hours paw - watering all your potted plants ! or else , read along and learn how to set up up an automated drip irrigation arrangement to water pots , wine barrels , rise bags or other containers . drip mould irrigation willsave you meter , water , and energy . This is also the perfect answer for when you go out of town . Plus , container have the inclination to dry out more quickly than raised garden beds or in - ground patch , making it even more helpful to have auto drip . Then your potted plants will get the uniform wet they need to boom !

A half wine barrel is full of garden soil, there is a ring around the center of the barrel made out of drip line tubing for irrigating containers.

This article will coverthree different optionsto mark up drip mould irrigation for container or pots :

Looking to set up drip irrigation forraised garden beds ? Seethis tutorial on set up drip mold tapein raised beds , orthis excess - easy raised bed drip systemthat link up to a faucet . Also , this guidecovers more tips on gardening in wine-coloured barrel – include how to prep them for planting , soil , example plant spacing , and more .

Option 1: Connecting Drip Irrigation to Pots from an Existing Drip Line

Or , if your survive drip mold ½ ” independent line is a act further away , you’re able to easilyextend itto be close to your pots . only cut the existing main line with sharp scissors , add together a½ ” couplerortee , and then link up a fresh section of ½ ” irrigation tube to prolong the exist line where demand . Cap the capable remnant of the new main line with afigure 8 clamp .   fend off distances much over 100 feet to observe good pressure in the line .

Would you like to save this?

We ’ll email this post to you , so you could derive back to it later on !

I agree to receive email updates .

revealing : Homestead and Chill is referee - supported . When you purchase through links on our site , we may earn an affiliate commission .

A tall blue ceramic pt with a marigold planted in it is next to a black fence. Drip tubing is visible a couple feet away from the pot with 1/4 inch micro tubing running along the fence towards the pot. Two orange lines have been superimposed on the photo to show the line in which the drip tubing is running to connect drip irrigation to the pot.

Supplies Needed

Instructions

Drip Emitter Options for Containers

It ’s easy tocustomizea container drip irrigation system to meet theunique needs of your plant life , clime , or pot size ! However , it ’s hard for me to say on the button how much you ’ll need to irrigate . There are just too many variables . In ecumenical , most flora choose a logical tearing schedule that dampens the soil deep , but is also allowed to dry out out ever - so - lightly between lacrimation . Plants breathe through their ancestor , so most do not enjoy constantly soggy ground . The emitter you choose and the duration you lead your drip organisation will influence how much water each plant receives .

For larger containers or plants that enjoy ample moisture , use abubblerormicro - spinkler(several if needed ) . Those offer a higher GPH flow and will water more surface expanse . For smaller pots or drought - tolerant plants , a individual 1 GPH or 2 GPHdrip emittermay be sufficient .

you’re able to also notice specialised drip emitter rings that are made for watering containers – like this5 inch ring , orthis 10 inch option . Or , see how wemake our own dripping ringsbelow ! They can be customized to any pot sizing , including wine-coloured barrels orextra tumid grow bags . Another optional step is to add a1/4″ valveto the course feed each container so you may shut off water supply to individual pots if needed .

A three part image collage, the first image shows a tall blue ceramic pot with a marigold planted in it. Drip tubing is visible leading into the top of the pot. The second image shows the 1/4 tubing connected to 1/2 inch drip tubing with a barbed connector. The third image shows a drip emitter at the end of the 1/4 inch micro tubing that will water the pot.

Option 2: Creating a New Drip Irrigation System for Pots From a Faucet or Garden Hose

It ’s easy to set up a new drip irrigation system of rules for pots from an outdoor spigot , or even connected right to the final stage of a garden hose . Zero plumbing skills are involve ! Though you ’ll need a few additional supply ( plus those already list above in alternative 1 ):

Supplies

|

notice : If your faucet ismore than 100 feet awayfrom your containers , confiscate a durablegarden hoseto the faucet first . range it out towards the containers , and then get laid on the 4 - in-1 drip mold adapter at the far close of the garden hose ( opposite the faucet ) . This fashion , the garden hosepipe will maintain salutary ( higher ) press before it ’s reduced at the adapter / drip connection . Hopefully you may keep the hose tuck away ( e.g. alongside the house , or under bush ) so it ’s not a tripping peril or eyesore .

Option 3: Connecting Drip Irrigation for Containers to PVC

One last option to coif up dripping irrigation for pots is to join a novel drip mold personal credit line to PVC . We just recently did this in our unexampled garden . We tip into the PVC lines that irrigate our raised garden beds to summate drip for 6 nearby wine cask . learn out the whole step - by - step picture below !

And that is how to set up a drip irrigation system for containers and pots.

An agave plant in a pale green ceramic pot is shown with 1/4 inch brown poly tubing inserted into the center of the pot with a brown emitter at the end of the line. Drip irrigation in pots can be fine tuned to the plants that need watering.

A four part image collage, the first image shows a hand punch tool being used to create a hole in 1/2 inch drip tubing, the second image shows a barbed 90 degree angle on the end of 1/4 inch micro tubing, the third image shows a barbed valve next to half inch tubing, the fourth image shows the barbed valved connected to 1/4 inch micro tubing on each end which can be used to turn on or off the valve.

1/4 inch micro tubing running between a rock border to a half wine barrel to connect drip irrigation to the pot.

DeanaCat’s hand is holding a drip ring that was constructed with 1/4 drip emitter tubing and a barbed tee.

A close up image of a drip ring that was made with 1/4 drip emitter tubing that is watering a wine barrel. Set up drip irrigation in pots for easy watering.

A half wine barrel with half inch drip tubing trenched in gravel next to it. 1/4 inch tubing is connected to the half inch tubing and is running up the side of the barrel to water the container with a circular 1/4 inch drip emitter tubing.

Drip irrigation in pots is set up in three half wine barrels set alongside a rock lined border. The drip is from a main drip line a few feet away that is covered in the bark mulch of the nearby flower bed.

An outdoor faucet with a hose timer and 4 in 1 adapter connected to drip tubing that is running towards a flower/pollinator plant bed that is around 10 feet away.

An outdoor hose bib is connected to a time with a 4 in 1 adapter that connects to half inch drip tubing.

A half inch drip tubing is covered in bark mulch inside a rock lined planting space. 1/4 inch micro tubing is connected to the main line and is running up the side of a half wine barrel, connecting to drip emitter tubing in the shape of a circle that waters the barrel. Drip irrigation in pots makes it easy to water consistently.

Six wine barrels arranged in a circle with a trench running inside the wine barrels with 1/2 inch drip tubing connected to each barrel with micro tubing and drip emitter tubing formed into a circle to water each barrel. Create drip irrigation for pots to make watering easier.

All the parts needed to create a drip system while converting PVC to 1/2 inch drip tubing. Each supply is shown in order with its name under each item. There is 1/4 inch drip emitter tubing , solid 1/4 inch micro tubing, scissors, 1/4 inch barb tee, 1/4 inch barb valve, 1/4 inch barb coupler, threaded coupling for PVC, adapter to connect 1/2 inch drip to PVC line, tee and valve, and 1/2 inch poly drip tubing.

A four part image collage, the first image shows an existing PVC line in the ground with an attachment on the end, one end is glued onto the PVC while the other end is threaded. Another piece is being held next to it which will screw onto the adapter and connect to 1/2 inch irrigation tubing. The second image shows the piece screwed onto the adapter, connected to the PVC and 1/2 inch tubing is being pushed onto the piece to transition to 1/2 inch tubing from 3/4 inch PVC. The third image shows the connected pieces following along a trench in the gravel. The fourth image shows a Tee piece with a valve being connected to the tubing.

A close up of gravel that is trenched to fit a half inch drip line to connect drip irrigation to the wine barrels that are nearby.

Six half wine barrels are aligned in a large circle, a trench is dug in the gravel in a circle inside the wine barrels. There is a half inch irrigation tub running around the inside of each wine barrel to connect drip irrigation to pots. Each half wine barrel has a small emitter drip line in the shape of a circle on the top of the soil surface.

A tear drop shaped clay vessel is being held up in front of half wine barrels full of soil. Beyond there are numerous wood raised beds, some of them full of vegetable plants. A large water fountain is off to the left of the center of the image.

DeannaCat signature, keep on growing